Intervlan routing using a router on a stick module

INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE HOW TO
INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE SOFTWARE
INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE PASSWORD
INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE SERIES

Note: In the example, the VTP mode is set to be transparent. Use the set vtp command to set the domain name and mode: Cat5500> (enable) set vtp domain mode transparent Last Updater V2 Mode Pruning PruneEligible on Vlans Vlan-count Max-vlan-storage Config Revision Notifications

INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE PASSWORD

The default VTP configuration on the switch is: Cat5500> (enable) show vtp domainР”Вomain Name Domain Index VTP Version Local Mode Password Understanding and Configuring VLAN Trunk Protocol (VTP) For more information on VTP, refer to this document: This has to be defined regardless of the number of switches in the network (one or many), and regardless of whether you are using VTP to propagate VLANs to other switches in the network. If the switch is a VTP server, you must define a VTP domain name before you can add any VLANs. You can also use the set ip route default 172.16.80.1 command to configure the default gateway instead of using the set ip route 0.0.0.0 172.16.80.1 command.Р”В¬onfigure the required number of VLANs on the switch.Р”Р„ccording to the Network Diagram, you need to configure two new VLANs (VLAN 10 and VLAN 20) on the switch.Р”В«efore you can create a new VLAN, the switch must be in VLAN Trunk Protocol (VTP) server mode or VTP transparent mode. Note:Р’В If you want to manage a switch that is on the other side of a router, you need to configure a default gateway on the switch, since the switch does not participate in IP routing and therefore has no knowledge of the РµвЂ¦С“ topology of the network. Interface sc0 IP address and netmask set.Р”В¬at5500> (enable) set ip route 0.0.0.0 172.16.80.1 !- Configure the default gateway. Use this set of commands to configure the Catalyst switch for management: Console> enable) set system name Cat5500 !- Configure the system name.Р”В¬at5500> (enable) set interface sc0 172.16.80.40 255.255.255.0 !- Configure the IP address.

INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE SERIES

If you have difficulty with access to the console, refer to these documents:Р”Р‡or Catalyst 5500/5000 series switches- Connecting a Terminal to the Console Port on Catalyst Switches.Р”Р‡or Catalyst 6500/6000 series switches- Connecting a Terminalsection of Connecting a Terminal to the Console Port on Catalyst Switches and Connecting a Modem section of Connecting a Modem to the Console Port on Catalyst SwitchesР”В¬onfigure the switch for basic management. This section provides a summary of the main configuration tasks that are performed in this document:Р”В¬onfigure the internal router for managementР”В¬omplete these steps to configure interVLAN routing on the Catalyst switch:Р”Р„ccess the console port on the Supervisor Engine. See the Common Issue: VLAN Interface Shows down/down section for details. This document points out a common problem that customers report when they configure interVLAN routing or multiple VLAN interfaces on the router module. Note:Р’В Do not connect workstation1 and workstation2 unless you are asked to do so in this document. ConventionsР”Р‡or more information on document conventions, refer to the Cisco Technical Tips Conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment. The configurations on all devices were cleared with the clear config all and write erase commands to ensure that they had a default configuration.

INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE SOFTWARE

RSM (WS-X5302) that runs Cisco IOSР’В® Software Release 12.0(5)W5(12)

Supervisor Engine Module (WS-X5530) that runs CatOS 6.1(1) software

The information in this document is based on these software and hardware versions: For those details, refer to these documents:Р”В¬onfiguring the Module for InterVLAN Routing section of Installation and Configuration Note for the Catalyst 4000 Layer 3 Services ModuleР”В¬onfiguration and Overview of the Router Module for the Catalyst 4000 Family (WS-X4232-РµвЂ¦С“)

INTERVLAN ROUTING USING A ROUTER ON A STICK MODULE HOW TO

Note:Р’В This document does not discuss how to configure interVLAN routing on Catalyst 4500/4000 switches using the РµвЂ¦С“ services module (WS-X4232-РµвЂ¦С“). Readers of this document should have knowledge of these topics: Route Switch Module (RSM) on the Catalyst 5500/5000 series switchesР”Р„ny Catalyst 5500/5000 or Catalyst 6500/6000 series switch running CatOS with a supported РµвЂ¦С“ card could have been used in this document to obtain the same results. Route Switch Feature Card (RSFC) on the Catalyst 5500/5000 series switches MSFC2 on the Catalyst 6500/6000 series switches Multilayer Switch Feature Card (MSFC) on the Catalyst 6500/6000 series switches The term internal router refers to these РµвЂ¦С“ cards/modules on the Catalyst 000 switches: This document provides basic information on how to configure interVLAN routing on a Catalyst switch (running Catalyst OS system software) using an internal router (Layer 3 card/module).

Intervlan routing using a router on a stick module